Products

Suits Ford 9 Inch Replacement for stock style crush sleeve/collar Collapsible spacer installs on the pinion and preloads the pinion bearings Note...

Suits Ford 9 Inch Steel pinion nut 3/4"-16 thread Red thread locking compound pre-applied

Suits Ford 9 Inch Includes: Pinion bearing housing shims Pinion bearing shims Pinion crush sleeve Pinion nut Note: this is a shim kit only. Th...

Suits Ford 9 Inch Designed to suit the Daytona style pinion support, being attached to an iron housing

Polished cast aluminium Will fit most 4 BBL carburettors with a 5-1/8” neck including Holley, Edelbrock, and Carter The unit includes 2 air cleane...

Polished cast aluminium Will fit most 4 BBL carburettors with a 5-1/8” neck including Holley, Edelbrock, Carter Supplied with front mesh insert, a...

Polished 6061-T6 billet aluminium Features recessed centre with ABS plastic horn button Suits all Cal Custom & Triple A 3 bolt steering wheel ...

Polished aluminium finish Push-in design Twist apart style for easy cleaning Specifically designed to fit valve covers with 1.25” holes including ...

Polished aluminium finish Push-in design With PCV Twist apart style for easy cleaning Specifically designed to fit valve covers with 1.25” holes i...

Smooth Top Shotgun Scoop Polished aluminium Suits single or dual 4 barrel carburetor/s (5-1/8” neck) Supplied with two paper filters, linkage, but...

3 Butterfly Street Scoop Polished aluminium Suits single or dual 4 barrel carburettor/s (5-1/8” neck) Carburettors must be mounted sideways Suppli...

Polished cast aluminium Billet oil cap With coil mounts Baffled with side vent port Fits all ignition coils with 72mm spacing Includes gaskets and...

Finned Shotgun Scoop Polished aluminium Suits single or dual 4 barrel carburetor/s (5-1/8” neck) Supplied with two paper filters, linkage, butterf...

Polished finned aluminium A great way to organize spark plug leads and clean up your engine compartment This kit will fit 1955-85 engines or any t...

Polished finned cast aluminium Suits LS1 LS2 LS3 LS6 LS7 2-piece design covers the factory coil locations without the need for relocation brackets...

Black finned cast aluminium Billet oil cap Without coil mounts Baffled with side vent port Includes gaskets and bolts   Engine Application: Sui...

Polished aluminium finish Push-in design Raised fin design and rounded corners (modelled on the performance factory valve covers of the 1950s &...

Cast finned aluminium Polished finish Push-in design Raised fin design and rounded corners (modelled on the performance factory valve covers of th...

Suits 1932 Ford Highly polished stainless steel with hidden welds

Polished stainless steel 150mm X 30mm Suitable for cannon style mufflers or most 6” round mufflers Part Number: AAA-63-C150

Red polyurethane hanger 2 hole design Holes suit 12mm hanger rod Measurements: 73mm long 47mm wide 20mm thick 40mm hole centres

Black polyurethane hanger 3 hole triangular design Holes suit 10mm hanger rod Measurements: 91mm long 60mm wide 23mm thick 42mm and 60mm hole cen...

Red polyurethane hanger 4 hole design Holes suit 12mm hanger rod Measurements: 108mm long 45mm wide 20mm thick 39mm, 57mm and 75mm hole centres (...

Fits Pontiac 301 326 350 389 400 455 Is recommended for stock and street performance engines For use on engines up to 400 HP Features 8 PSI shut-o...