GM

Polished cast aluminium Billet oil cap With coil mounts Baffled with side vent port Fits all ignition coils with 72mm spacing Includes gaskets and...

Precision machined billet aluminium - NOT PLASTIC Prevents unfiltered oil from entering the bearings/lifters etc. by blocking off the oil bypass c...

Suits: Small Block Chevrolet Big Block Chevrolet LS & LT Duramax Machined from billet aluminium 1/2" thick plate Allows you to utilise all ...

For mounting LS2/LS3 water pumps to engines fitted with LS1 crank pulley, to ensure proper belt alignment Each spacer is 18mm thick One spacer inc...

To suit LS engine conversion into 1973-1998 Chevrolet/GMC pickup trucks Lasercut mild steel Black powder coated Each of the 4 mounting slots are 3...

Suits Holden and HSV: VT, VY, VZ fitted with LS1/LS2 engine Includes smaller diameter harmonic balancer pulley for reduced inertia allowing for...

Suits GM LS1 LS2 LS6 Stainless steel Suits 3/8" studs 1.8 ratio High quality steel rollers, roller bearings, and trunions Full set including posi/...

Suits early Holden 253 308 (pre-EFI heads) Fabricated aluminium Black anodised Welded-in baffles 85mm tall (overall) With breather holes Includes ...

Suits early Holden 253 308 (pre-EFI heads) Fabricated aluminium Welded-in baffles 85mm tall (overall) With breather holes Includes bolts Note: ga...

Designed to eliminate trapped air and steam from the coolant ports in the cylinder heads. Helps to prevent hot spots and overheating. Billet alumi...

Direct replacement for factory 4MV Rochester Quadrajet (replaces 1901) This will NOT suit Holden factory applications as it is configured to suit ...

Converts stock rocker arms into captured roller trunnions for high RPM applications Cost effective alternative to a billet roller rocker setup Inc...

Helps to prevent first start engine wear or damage by pre-lubricating and pressurising the oil system, without having to start the engine Heavy du...

6061-T6 billet aluminium construction Precision machined For mounting an LS3 style MAF sensor to a custom intake pipe Underside of the bung has a ...

Suits GM LS2 Premium engine gasket set Superior sealing and precise fitment Quality and cost effective solution for rebuilding or overhauling your...

Suits SBC engines with 1 piece rear main seal Premium engine gasket set Superior sealing and precise fitment Quality and cost effective solution f...

Suits Holden HQ HJ HX HZ WB Machined from high quality 6061-T6 billet aluminium Black finish Replace your stock stamped steel hinges and springs N...

Suits Chevy Camaro 1967 1968 1969  Machined from high quality 6061-T6 billet aluminium Silver finish Replace your stock stamped steel hinges and s...

Suits Chevy Camaro 1967 1968 1969  Machined from high quality 6061-T6 billet aluminium Black finish Replace your stock stamped steel hinges and sp...

Large intake bore provides maximum airflow for mid to high range horsepower engines Perfect match for the Calflow Fabricated LS intake manifolds (...

Large intake bore provides maximum airflow for mid to high range horsepower engines Perfect match for the Calflow Fabricated LS intake manifolds (...

Large intake bore provides maximum airflow for mid to high range horsepower engines Perfect match for the Calflow Fabricated LS intake manifolds (...

Billet aluminium adaptors Braided stainless hose Black finish Fits front or rear of the engine. Includes blanks Requires thread sealant when fitti...

The Velocity fabricated aluminium intake manifold is the ultimate in NA and forced induction performance for your LS3 L98. The intake runners are v...