GM

Fits all SB Chevy engines 1985 up with right hand (Australian driver side) dipstick 1 piece rear main seal These are stock capacity oil pans Comes...

Seal Kit to suit GM 1-1/8 inch Bore Master Brake Cylinder Kit includes 5 seals Suits all Cal Custom 1-1/8 inch bore GM Master Brake Cylinders

Seal Kit to suit GM 1 inch Bore Master Brake Cylinder Kit includes 5 seals Suits all Cal Custom 1 inch bore GM Master Brake Cylinders

Replaces RYCO A1557 & KN33-2919 Minimum 5% Horsepower Gain Brand New Genuine Simota High Air Flow Panel Filter To Suit: Holden/HSV VE-VF V8 6...

Chrome Plated Steel Flywheel Dust Cover Fits Chevy/GM Powerglide automatic transmissions for Small Block and Big Block Chevy V8 engines Only suits...

GM style brake proportioning valve to suit vehicles using front disc/rear drum brakes All brass construction, precision manufactured. Single wire ...

Faithful reproduction of the original Chevy exhaust manifold also known as the rams horn style exhaust manifold Raw cast iron finish 2-1/2" Outlet...

Suits 265 283 305 307 327 350 383 400 396 402 427 454 472 502 348 409 Small and Big Block Chevy motors 15º outlet. 360 degree swivel for easy posi...

Machined from 6061 T6 billet aluminium Fits 265 283 305 307 327 350 383 400 396 402 427 454 472 502 348 409 Small and Big Block Chevy motors Clear...

Suits Holden HT-VH 253 308 Early Natural Finish Aluminium Casting Aluminium composition dissipates heat more efficiently than the factory cast iro...

Suits Small Block Chev with short water pump Positions alternator on the upper left side (Aus passenger side) Includes all three brackets as pictu...

Suits GM Gen.4 LS2, LS3 etc. For displacement on demand engines This cover is only for those wanting to delete the DOD system This cover featu...

Suits: Small Block Chevrolet Big Block Chevrolet LS & LT Duramax Machined from billet aluminium 1/2" thick plate Allows you to utilise all ...

For mounting LS2/LS3 water pumps to engines fitted with LS1 crank pulley, to ensure proper belt alignment Each spacer is 18mm thick One spacer inc...

To suit LS engine conversion into 1973-1998 Chevrolet/GMC pickup trucks Lasercut mild steel Black powder coated Each of the 4 mounting slots are 3...

Suits Small Block Chev and Big Block Chev engines Quality zinc die-cast with beautiful chrome plated finish Includes rubber o-ring

Holden rocker cover OEM style with 2 baffled breather holes and twist-in oil cap provision Precision manufactured in steel and then triple chrome ...

Suits Holden and HSV: VT, VY, VZ fitted with LS1/LS2 engine Includes smaller diameter harmonic balancer pulley for reduced inertia allowing for...

Suits Small Block Chev and Big Block Chev engines Quality zinc die-cast with beautiful chrome plated finish Comes complete with thermostat housing...

Set of 8 bolts and 8 washers Chrome plated 1/4"-20 x 3/4" Suitable for SBC and other applications

Suits GM LS1 LS2 LS6 Stainless steel Suits 3/8" studs 1.8 ratio High quality steel rollers, roller bearings, and trunions Full set including posi/...

Suits early Holden 253 308 (pre-EFI heads) Fabricated aluminium Black anodised Welded-in baffles 85mm tall (overall) With breather holes Includes ...

Suits early Holden 253 308 (pre-EFI heads) Fabricated aluminium Welded-in baffles 85mm tall (overall) With breather holes Includes bolts Note: ga...

Suits GM LS1 LS6 engines with the cable throttle body Engine bolt kit Stainless steel Durable and corrosion resistant Not suitable for drive by wi...